What You Will Need:

Tools:*

Caulk Gun (See on Amazon)

Flat Pry Bar (See on Amazon)

Hammer (See on Amazon)

Roofing Trowel (See on Amazon)

Wire Brush (See on Amazon)

Materials:*

Plastic Roof Cement, Trowel-Applied (See on Amazon) or

Plastic Roof Cement, Caulk Gun-Applied (See on Amazon)

Sheet Metal Flashing (See on Amazon)


Introduction:

A well-designed roof made with robust materials not only adds to the splendor of the structure but also provides superior protection against the elements. Despite being relatively expensive and heavy, tile roofs are popular because of their appearance and durability. People invest in tile roofs because they can last a hundred years or more.

 
Replace broken tiles to prevent roof leaks.

Replace broken tiles to prevent roof leaks.

 

Fired clay, terra cotta, and molded, tinted concrete are standard tile materials. Tile roofs made with these earth minerals can survive storms, high winds, and even fire. They are energy-efficient, resistant to decay and insect damage, and provide a low maintenance roof. But as with every other material thing, damage can still occur: damage from wind, debris falling on the roof, freezing weather, the stresses of snow or water, the heat of the sun, and even accidental damage caused by humans stepping on them or hitting them while working on or near them.

The damage mostly ends up affecting individual tiles. Often the damaged tiles do not need to be replaced, and some minor adjustment and repair will be enough. The repair cost will depend on the type of damage and the number of damaged tiles, and also which company you hire for the job. However, if the issue is not too complicated, some basic knowledge and a steady ladder can help you solve the problem all by yourself!

Identifying the problem:

Tile roofs should be visually inspected every three months to check for cracks and other damage. Gutters should be cleaned out monthly so that no debris can accumulate. If a problem is found, a fast response is needed since damaged tiles or worn out underlayment can cause leaks which lead to ever-increasing water damage to the building. More damage will cost more to repair.

To solve any problem, the first step is to properly identify the reason for the damage and the exact points where the repairs need to be done. If you are determined to handle the repairs without professional help, some basic knowledge is a must. There could be several reasons for damaged clay tiles, and issues can result from problems with other parts of the roof.

Common issues with tile roofs that need attention are:

  • Tiles with minor cracks or holes

  • Broken tiles

  • Build-up of debris in the roof valley

  • Defects in the underlayment

Safety First and Proper Preparation Next:

Before getting on the roof, you should have leather gloves and protective safety glasses. A stable, properly set up ladder is critical to safely accessing the roof. See here for guidelines on ladder safety. When working on roofs, a personal fall arrest system should be used for protection against falling (see here for information on personal fall arrest systems). More roof safety information can be found here.

While working on damaged tiles one should be careful not to damage any other parts of the roof. The tools and materials that you will be using should be kept within reach. These items may include a wire brush, nails, wet saw, hammer, mortar, crowbar, glue, roofing cement or plaster, caulk and caulk gun, waterproof membrane, roofing felt, and tile roof sealer or terracotta color. If a tile needs to be replaced, it should be replaced with the exact same type of tile. If you don’t already have spare matching tiles, they should be available from the original supplier or manufacturer. Trying to force another type of tile to fit in might cause more damage.

Estimating the Cost:

A DIY tile roof repair can save you money on hiring a roofer. But you should also have an idea of what the tools and materials will cost. If you’re not sure of this, take some pictures, measure the roof and the damaged areas, and go to the local home improvement or hardware store and ask them to help with an estimate. Cost factors will include the extent of the damage (amount of material needed) as well as the brands and quality of the materials you use. If a repair job is not correctly projected and estimated, you will often end up spending more than you need to.

Do-It-Yourself Tile Roof Repairs:

Different issues require different solutions. After identifying the problem, and using proper precaution and the necessary tools, repairs can be made in the following ways without professional help:

Small Cracks or Holes

When there are small cracks and holes in tiles, plastic roofing cement can be used to fill in the defects.

  • First, clean the damaged area with a wire brush.

  • Use plastic roofing cement to fill a hole or to seal or join the crack.

  • With a trowel, smooth the surface.

Cracked or Broken Roof Tile

When a roof tile is broken and missing a piece, or a crack is so big that a piece of the tile becomes loose, then the tile needs to be replaced.

  • Use a flat pry bar to carefully lift up the tile (or tiles) just above the cracked or broken one. Be careful not to damage them by lifting them too far. Prop them up with blocks of wood.

  • Next use the flat pry bar to lift out the faulty tile. If it doesn’t come out, insert a piece of wood beneath the tile to protect the tile below it. Use a hammer or the flat bar to carefully break the tile and remove the pieces. Using the flat bar, remove the nails that held the damaged tile if you can. If you can’t, use the flat bar and a hammer to drive the nails down into the battens or roof sheathing.

  • At this point, apply a bed of roofing cement to the area that was covered by the tile that’s being replaced, and slide in the new tile. Nails are not required for the replacement tile; the cement or adhesive should be good enough to hold it.

  • Now gently lower the raised tiles back into place.

If a cracked roof tile cannot be replaced right away, a temporary repair can be made by cutting a piece of roofing felt, waterproof membrane, or flashing strip to size and sticking it over the crack with roof adhesive, completely covering the damaged area.

Tile Roof Leaks

Leakage is a rather complicated problem. To solve it, you need to identify and repair the source of the leak. To identify the source of the leak, you should perform a visual inspection of the roof surface. Before getting up on the roof, note that wet spots, watermarks, stains, or discolorations on the underside of the roof may be seen in the attic. With the attic light turned off, daylight may even be seen through the hole. This will give you an idea as to where to look on the roof. If you still can’t find it, run water onto the roof with a hose, and water from the leak should appear in the attic. If you can identify a hole as the source of the leak, push a nail or a piece of thin wire through the hole from below to mark it for when you are on the roof.

  • Use a flat pry bar to lift up the tiles around the leak.

  • Using roofing cement, fill the hole.

  • Replace the tile if broken or cracked.

  • If there is long-term water damage to the supporting roof structure that has caused sagging, the wood sheathing and rafters underneath the roof tiles probably need to be fixed first. Contact a roofing contractor.

Fast Fix for a Roof Leak

A roof leak due to a hole in the tile can sometimes be temporarily fixed with sheet metal flashing, commonly available at hardware stores.

  • Take a 12-by-12-inch piece of galvanized sheet metal flashing.

  • Lift the damaged tile with one hand and cover the hole by pushing the metal flashing piece up under the tile. Set the piece of metal in flashing cement to hold it in place.

More Tips:

  • If you know there’s a problem with your roof, but you’re not exactly sure what needs to be done to fix it, you can call a professional roofer for an inspection and detailed quote, free of charge. The roofer should give you a good idea as to what needs to be done.

  • Safety is a must! Rubber-soled shoes are great for good traction on the roof. Use a safety harness. Don’t work alone. Be careful on the ladder and have someone to hold it steady for you. Tie the ladder off to prevent it from slipping.

  • Avoid working in freezing cold or rain.

  • Do not work on a roof if there are thunderstorms in the area.

  • Discard any broken and loose tile.

  • A putty knife can be used to apply roofing cement to small cracks or holes.

Even one single broken tile can create havoc by causing water leaks or sun damage to waterproof underlayment. Steps should be taken before the damage is done. Making your own repairs may be a good way to save money when the problem is fairly simple. For more serious issues with your tile roof, find a qualified roofer to make the repairs as soon as you can; otherwise worse things can happen, including severe structural damage.

Related Pages: